MELLANOX MCX342A-XCAN NETWORK CARD TREIBER WINDOWS 7

MELLANOX MCX342A-XCAN NETWORK CARD DRIVER DETAILS:

Type: Driver
File Name: mellanox_mcx342a_12530.zip
File Size: 11.7 MB
Rating:
3.76
14 (3.76)
Downloads: 10
Supported systems: Windows 10, Windows 8.1, Windows 7
Price: Free* (*Free Registration Required)

Download Now
MELLANOX MCX342A-XCAN NETWORK CARD DRIVER



Drivers from Mellanox

Over-temperature This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: To guarantee proper air flow, allow at least 8cm 3 inches of clearance around the ventilation openings. During Lightning - Electrical Hazard During periods of lightning activity, Mellanox MCX342A-XCAN Network Card not work on the equipment or connect or disconnect cables.

MELLANOX MCX342A-XCAN NETWORK CARD WINDOWS 8 DRIVER DOWNLOAD

Equipment Disposal Disposal of this equipment should be in accordance to all national laws and regulations. Local and National Electrical Codes This equipment should be installed in compliance with local and national electrical codes. Hazardous Radiation Exposure Caution — Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure. When connected to a PCIe Gen3 environment, firmware configures the card to use 4 lanes upon bring up. All other Mellanox MCX342A-XCAN Network Card power voltages are generated by on-board switch mode regulators.

There is a jumper on each Mezzanine card that indicates to the device whether an on-board Flash device is to be used or not. Table 4 provides information on this jumper.

NEW DRIVERS: MELLANOX MCX342A-XCAN NETWORK CARD

Please consult the host machine documentation for instructions on how to install a PCI Express Mezzanine connector. If the card is installed in a PCI Mezzanine connector with less lanes than the card requires then the Mezzanine card will not provide the optimum data transfer. Open Device Manager on the server. Select Properties to display the Mezzanine card properties window.

Mellanox ConnectX-4 50Gigabit Ethernet Card MCXA-GCAT

Mellanox Technologies 21 Rev 1. Follow the installation instructions included in the download package also available from the download page. To ensure that communication has been established follow the instructions below. To assign an IP address to the interface run: To check driver and device information run: Download this package from the Mellanox web site at: To display a summary of network Mezzanine software- firmware- and hardware-related information such as driver version, firmware version, bus interface, Mezzanine identity, and network port link information, perform the following steps: Device Manager Example Step 2: Select the Information tab from the Properties sheet example. To save this information for debug purposes, click Save To File Mellanox MCX342A-XCAN Network Card provide the output file name.

Mellanox Technologies Mellanox MCX342A-XCAN Network Card Rev 1.

For more information go to http: Firmware is updated occasionally, and the most recent firmware can be obtained from: Check that the firmware on your card is the latest Mellanox MCX342A-XCAN Network Card on the Mellanox site, if not update to the latest version found on the Mellanox web site. Firmware can be updated on the stand alone single card using the flint tool of the Mellanox Firmware Tools MFT package.

A firmware binaries table lists a binary file per Mezzanine card. The file name of each such binary is composed by combining the firmware name, the firmware release version, and the card part number. Mellanox®, Mellanox logo, BridgeX®, ConnectX®, CORE-Direct®, Mellanox MCX342A-XCAN Network Card, InfiniHost®, InfiniScale®, PhyX®.

Chapter 3 Ethernet Mezzanine Card Installation. Dual-port MCXA-XCAN Mezzanine Card,” on. Mellanox MCXA-XCCN ConnectX-3 EN Network Interface Card for OCP 10GbE Dual-Port SFP+ PCIe x8 IPMI disabled No Bracket RoHS g: XCAN.

Other Drivers